ASROCK FATAL1TY Z77 PROFESSIONAL-M ASMEDIA SATA DRIVER DETAILS:
|File Size:||38.7 MB|
|Supported systems:||Windows XP/Vista/7/8/10, MacOS 10/X|
|Price:||Free* (*Free Registration Required)|
ASROCK FATAL1TY Z77 PROFESSIONAL-M ASMEDIA SATA DRIVER
Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries ASRock Fatal1ty Z77 Professional-M ASMedia SATA you and damages to motherboard components. Do not over-tighten the screws! Doing so may damage the motherboard. Unplug the power cord from the wall socket before touching any components. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components. Hold components by the edges and do not touch the ICs.
ASROCK FATAL1TY Z77 PROFESSIONAL-M SERIES USER MANUAL Pdf Download.
Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component. When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws!
Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Do not force to insert the CPU into the socket if above situation is found. ASRock Fatal1ty Z77 Professional-M ASMedia SATA, the CPU will be seriously damaged. Step 1. Open the socket: Step Disengage the lever by pressing it down and sliding it out of the hook.
You do not have to remove the protection cover. Keep the lever positioned at about degrees in order to flip up the load plate. Step 2. Locate Pin1 and the two orientation key notches. Hold the CPU by the edge which is marked with a black line.
|ASUS VivoBook S200E ATKACPI||SATA Performance|
|Acer Aspire 5620 Chipset||You are here|
|Toshiba Satellite P70T-A Genesys Card Reader||57 Comments|
|HP lt4120 Snapdragon X5 LTE NMEA||Customer review|
Carefully place the CPU into the socket. Verify that the CPU is within the socket and properly mated to the orient keys. Step 3. Close the socket: Flip the load plate onto the IHS.
Press down the load lever, and secure it with the load plate tab under the retention tab. The protection cover will automatically come off by itself.
Please save and replace the cover if the processor is removed. The cover must be placed if you wish to return the motherboard for after service. Please adopt the type of heatsink and cooling ASRock Fatal1ty Z77 Professional-M ASMedia SATA compliant with Intel Pin CPU to dissipate heat. Before you install the heatsink, you need to spray thermal interface material between the CPU and the heatsink to improve heat dissipation. Ensure that the CPU and the heatsink are securely fastened and in good contact with each other. For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink.
Below is an example to illustrate the installation of the heatsink for Pin CPUs.
Apply Thermal Interface Material Step 2. Place the heatsink onto the socket.
Align fasteners with the motherboard throughholes. Step 4. Rotate the fastener clockwise, then press down on fastener caps with thumb to install and lock.
Asrock z77 professional-m issue
Repeat with remaining fasteners. Fan cables on side closest to MB header Fastener slots pointing straight out Press Down 4 Places If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.
Step 5. Connect fan header with the CPU fan connector on the motherboard.
ASMedia controller on Fatal1ty Z77 Professional
Step 6. Secure redundant cable with tie-wrap to ensure the cable does not interfere with fan operation or contact other components. Fatal1ty Z77 Professional-M. 2 x Rear USB Gen1 ports by ASMedia ASM, support USB // up to 5Gb/s 1 x SATA 1 to 1 Power Cable. Hi Folks,This system has a Fatal1ty Z77 Professional ASRock Fatal1ty Z77 Professional-M ASMedia SATA which, uses two ASMedia SATA controllers to provide an additional 4 x SATA ports Now I'm not certain what is entailed in changing this parameter from.