ACTEL FLASHPRO 4 PROGRAMMER DRIVER DETAILS:

Type: Driver
File Name: actel_flashpro_19142.zip
File Size: 3.8 MB
Rating:
3.88
19 (3.88)
Downloads: 10
Supported systems: Windows 2008, Windows XP, Windows Vista, Windows 7/8/10
Price: Free* (*Free Registration Required)

Download Now
ACTEL FLASHPRO 4 PROGRAMMER DRIVER



Microsemi will be supporting the FlashPro Express v Whether you are programming a board containing a single device or multiple devices connected in a chain, you can quickly program and reprogram Microsemi flash FPGAs by connecting to a PC and the target board. Hardware Starting with Libero SoC v In-system programming using the JTAG port adds the flexibility of field upgrades or post-assembly production-line characterization. Production costs are significantly reduced as a result of elimination of expensive sockets Actel FlashPro 4 Programmer the board. Hence, all FlashPro hardware programmers are supported by each FlashPro software and user interface support, You do not have to replace software while you switch from one hardware programmer to another.

FlashPro's on-chip debug feature allows access to SmartFusion and Fusion-specific peripherals such as flash memory, analog-to-digital converter ADC and other FPGA and design-specific information Actel FlashPro 4 Programmer for verifying the implemented design. Provide a bitstream file with a user pass key 1 that matches the user pass key 1 programmed into the device. A or M2S Rev. This can be done with SoftConsole.

DOWNLOAD DRIVERS: ACTEL FLASHPRO 4 PROGRAMMER

See the Device Exit Codes for pre-v8. Exit codes with negative integers are reserved for vendor-specific EXIT codes. Also known as Checking Chain Error. Physical chain configuration has been altered. Something has become disconnected in the chain. The specific IR length of non- Microsemi devices may be incorrect. The order of the specified chain may be incorrect.

ACTEL FLASHPRO 4 PROGRAMMER DRIVER FOR MAC

Use latest version of FlashPro software. Reduce the length of ground connection. Try again at a slower TCK.

Actel Flashpro5 programming download cable Microsemi HARDWARE PROGRAMMER SOC / FPGA

Contact Microsemi Technical Support. Files not for M1, but target device is M1. File is for M1, but target device is not M1. Check that the target device is M7 Actel FlashPro 4 Programmer. Make sure that the programming file you generated is for an M7-enabled device. Measure JTAG pins, noise and reflection. Check that the target device is M1 enabled.

Make sure the programming file generated is for an M1-enabled device. Check the target device; make sure the programming file generated is matches the Actel FlashPro 4 Programmer device. Check that the target device is not M7 enabled. Make sure that the programming file generated is for non-m7 enabled device. Check that the target device is not M1 enabled. This device is supported with pre-v8. Make sure that the generated programming file is for non-m1 enabled device. Check that the target device is P1 enabled. Make sure programming file generated is for M1 enabled device.

FlashPro Microsemi

Contact Microsemi Technical Support Monitor related power supplies that cause the issue during programming; check for transients outside of Microsemi specifications. Monitor related power supplies that cause FlashPro User's Guide. Reset Actel FlashPro 4 Programmer is not properly tied off in your design. Inspect device using Device Debug. This could have occurred during standalone verify.

Measure JTAG pins, and noise or reflection. If the target Actel FlashPro 4 Programmer block is locked, then you must unlock it by erasing the security and then reprogramming with the desired security settings. If the target EFMB block is locked, then you must unlock it by erasing the security and then reprogramming with the desired security FlashPro User's Guide Try reprogramming.

Failed to program security lock settings. Incorrect AES key. Programming file generated Actel FlashPro 4 Programmer an older version of software Device is programmed with a different design. Unstable VCC Monitor related power supplies that cause the issue during programming; check for transients outside of Microsemi specifications. Generate a programming file with Actel FlashPro 4 Programmer correct AES key. FlashPro, Software for Windows platform, supporting all hardware programmers. Discontinued from Libero SoC v, FlashPro4, Hardware programmer. FlashPro is Microsemi's programming software tool for SmartFusion, IGLOO, ProASIC3, Fusion devices.

You will be able to navigate easily through the FlashPro.

Other Drivers